Correlation between Tensile Deformation Behavior and Microstructural Morphology of Nuclear Grade Austenitic Stainless Steel Weld Joints using Infrared Thermography Technique

##plugins.themes.bootstrap3.article.main##

A.K. Lakshminarayanan
R. Rajasekaran
M. Menaka

Abstrakt

Tensile deformation behavior of nuclear grade Austenitic Stainless Steel (SS) and its weld joints fabricated by Gas Tungsten Arc Welding (GTAW) and Activated flux Gas Tungsten Arc Welding (AGTAW) processes were studied and correlated with relevant microstructural morphologies using Infrared Thermography (IRT) technique. The microstructure of base metal showed a complete austenite phase. GTAW Fusion Zone (FZ) exhibited both primary ferrite and primary austenite mode of solidification. Meantime, AGTAW FZ exhibited only primary austenite mode of solidification A strain rate of 4.4x10-4 s-1 was used during the tensile test of the base metal and weld samples. The failure locations of the base metal, GTAW and AGTAW samples were noticed at the center of the gauge portion, the base metal side away from Fusion Line (FL) and Heat Affected Zone (HAZ) respectively. Temperature variations of the base metal and weld zones were recorded in the form of thermograms using the IR camera at the different stages of the tensile deformation. During deformation study, peak temperatures of 39.2 oC, 38.8 oC and 34 oC were observed at the base metal, GTAW and AGTAW samples respectively. The lesser peak temperature of the AGTAW sample compared to the base metal and GTAW samples indicated that the AGTAW sample undergone lesser deformation. Moreover, tensile deformation behaviors of the base metal and weld samples were correlated with their microstructural morphologies using corresponding temperature curves.

Pobrania

Brak dostępnych danych do wyświetlenia.

##plugins.themes.bootstrap3.article.details##

Jak cytować
[1]
A. Lakshminarayanan, R. Rajasekaran, i M. Menaka, „Correlation between Tensile Deformation Behavior and Microstructural Morphology of Nuclear Grade Austenitic Stainless Steel Weld Joints using Infrared Thermography Technique”, Weld. Tech. Rev., t. 92, nr 1, s. 7–15, sty. 2020.
Dział
Original Articles
Biogramy autorów

R. Rajasekaran - SSN College of Engineering, India

Research Scholar, Department of Mechanical Engineering

M. Menaka - Indira Gandhi Centre for Atomic Research, India

Scientific Office, Quality Assurance, Divsion, Indira Gandhi Centre for Research

Bibliografia

Mannan SL., Chetal S., Selection of materials for prototype fast breeder reactor, Transactions of the Indian Institute of Metals, 2003, Vol. 56(2), 155-178.

Kuang H.T., Chih Y.H., Performance of activated TIG process in austenitic stainless steel welds, Journal of Materials Processing Technology, 2011, Vol. 211, 503-512. DOI:10.1016/j.jmatprotec.2010.11.003 DOI: https://doi.org/10.1016/j.jmatprotec.2010.11.003

Ahmadi E., Ebrahimi A.R., Welding of 316L Austenitic Stainless Steel with Activated Tungsten Inert Gas Process, Journal of Materials Engineering and Performance, 2015, Vol. 24, 10651071. DOI: 10.1007/s11665-014-1336-6 DOI: https://doi.org/10.1007/s11665-014-1336-6

Vasudevan M., Effect of A-TIG Welding Process on the Weld Attributes of Type 304LN and 316LN Stainless Steels, Journal of Materials Engineering and Performance, 2017, Vol. 26(3), 1325-1336. DOI: 10.1007/s11665-017-2517-x DOI: https://doi.org/10.1007/s11665-017-2517-x

Bagavathiappan S., Lahiri B.B., Saravanan T., John P., Jayakumar T., Infrared thermography for condition monitoring A review, Infrared Physics and Technology, 2013, Vol. 60, 35-55. DOI: 10.1016/j.infrared.2013.03.006 DOI: https://doi.org/10.1016/j.infrared.2013.03.006

Sony P., Amretendu M., Rajdeep S., Zafir A., Dipak D, Vikas K., Determination of critical strain for rapid crack growth during tensile deformation in aluminide coated near-α titanium alloy using infrared thermography, Materials Science and Engineering A, 2013, Vol. 576, 217221. DOI: 10.1016/j.msea.2013.03.089 DOI: https://doi.org/10.1016/j.msea.2013.03.089

Górka J., Janicki D., Fidali M., Jamrozik W., Thermographic Assessment of the HAZ Properties and Structure of Thermomechanically Treated Steel, International Journal of Thermophysics, 2017, Vol. 38(183), 1-21.

DOI: 10.1007/s10765-017-2320-9 DOI: https://doi.org/10.1007/s10765-017-2320-9

Psuj G., Szymanik B., Łopato P., Herbko M., Maciusowicz M., Multimodal monitoring of damage in steel construction elements during fatigue life, Welding Technology Review, 2016, Vol. 88(10), 104-109.

DOI: 10.26628/ps.v88i10.695 DOI: https://doi.org/10.26628/ps.v88i10.695

Haneef T., Lahiri BB., Bagavathiappan S., Mukhopadhyay CK., Philip J., Rao BP., Jayakumar T., Study of the tensile behavior of AISI type 316 stainless steel using acoustic emission and infrared thermography techniques, Journal of Materials Research and Technology, 2015, Vol. 4(3), 241-53. DOI: 10.1016/j.jmrt.2014.12.008 DOI: https://doi.org/10.1016/j.jmrt.2014.12.008

Corigliano P., Crupi V., Epasto G., Guglielmino E., Risitano G., Fatigue assessment by thermal analysis during tensile tests on steel, Procedia Engineering, 2015, Vol. 109, 210-218. DOI: 10.1016/j.proeng.2015.06.215 DOI: https://doi.org/10.1016/j.proeng.2015.06.215

Corigliano P., Cucinotta F., Guglielmino E., Risitano G., Santonocito D., Thermographic analysis during tensile tests and fatigue assessment of S355 steel, Procedia Structural Integrity, 2019, Vol. 18, 280-286.

DOI: 10.1016/j.prostr.2019.08.165 DOI: https://doi.org/10.1016/j.prostr.2019.08.165

Pawlak S., Różański M., Muzia G., The application of active Thermography for non-destructive testing of brazed joints, Welding Technology Review, 2014, Vol. 85(2), 24-28. DOI: 10.26628/ps.v85i2.276 DOI: https://doi.org/10.26628/ps.v85i2.276

Pawlak S., Różański M., Stano S., Muzia G., Active Thermography as a new method of testing non-destructive laser welded lap joints, Welding Technology Review, 2014 , Vol. 86(3), 4-7. DOI: 10.26628/ps.v86i3.100 DOI: https://doi.org/10.26628/ps.v86i3.100

Vasudevan M., Bhaduri AK., Baldev R., Penetration enhancing flux formulation for tungsten inert gas (TIG) welding of austenitic stainless steel and its application, US8097826B2. https://patents.google.com/patent/US8097826B2/en

ASTM Designation: E 407 07: (2015) e1. Standard Practice for Microetching Metals and Alloys. https://www.astm.org/Standards/E407

Rajasekaran R., Lakshminarayanan A.K., Vasudevan M., Vasantharaja P., Role of welding processes on micro-structure and mechanical properties of nuclear grade stainless steel joints, Proceedings of the Institution of Mechanical Engineers, Part L: Journal of Materials: Design and Applications, 2019, Vol. 233(11). DOI: https://doi.org/10.1177/1464420719849448

DOI: 10.1177%2F1464420719849448

Ostromęcka M., Kolasa A., The effect of the current pulsation frequency on heat supply results during pulsed current TIG welding in 301L stainless steel, Welding Technology Review, 2019, Vol. 91(8), 61-71.

DOI: 10.26628/wtr.v91i8.1046 DOI: https://doi.org/10.26628/wtr.v91i8.1046

Vijayanand V.D., Vasudevan M., Ganesan V., Parameswaran P., Laha K., Bhaduri A.K., Creep deformation and rupture behavior of single-and dual-pass 316LN stainless-steel-activated TIG weld joints, Metallurgical and Materials Transactions A, 2016, Vol. 47(6), 2804-2814. DOI: 10.1007/s11661-016-3426-6 DOI: https://doi.org/10.1007/s11661-016-3426-6

Yan Z., Zhang H., Chen P., Wang W., Anisotropy of fatigue behavior and tensile behavior of 5A06 aluminum alloy based on infrared thermography, Journal of Wuhan University of Technology Materials Science Edition, 2017, Vol. 32(1), 155-161. DOI: 10.1007/s11595-017-1574-1 DOI: https://doi.org/10.1007/s11595-017-1574-1

Kumar J., Baby S., Kumar V., Thermographic studies on IMI-834 titanium alloy during tensile loading, Materials Science and Engineering: A, 2008, Vol. 496, 303-307. DOI: 10.1016/j.msea.2008.05.040 DOI: https://doi.org/10.1016/j.msea.2008.05.040

Kutin M., Ristić S., Burzić Z., Puharić M., Testing the tensile features of steel specimens by thermography and conventional methods, Scientific Technical Review, 2010, Vol. 60(1), 66-70.

Venkatraman B., Mukhophadyay C.K., Raj B., Prediction of tensile failure of 316 stainless steel using infrared thermography, Experimental Techniques, 2004, Vol. 28(2), 35-38. DOI: 10.1111/j.1747-1567.2004.tb00157.x DOI: https://doi.org/10.1111/j.1747-1567.2004.tb00157.x